Back

Alginate 3D Gel - 5 kg.

  • Alginate 3D Gel - 5 kg.

1-2 days

    € 99,50 Free shipping

    Add to wishlist

    • Fast shipping! Everything available from stock
    • Buy from the specialist
    • Shipping Worldwide
    • Not good? Money Back!
    Placeholder4.8

    Ratings

    Product description

    Alginate 3D Gel - 5 kg.

    Alginate 3-D Gel is 100% natural and suitable for copying body parts quickly and easily.

    Read the full product description

    The 3D Gel is easy to use, cured within minutes and takes over the smallest details. The gel is completely harmless to humans and the environment. One can simply throw this gel into the trash after use or use it in the compost heap.

    • Mixing ratio 1 part powder: 4 parts water (weight!)
    • Gel quickly
    • Easy to mix
    • Relatively strong after gelation
    • Takes over every detail
    • Nice (strawberry) odor
    • Chromatic from white to pink to white

    Technical data

    Mixing ratio (weight) for pouring or dipping

    [Water: gel]

    4: 1

    Mixing ratio (weight) for brushing or spreading

    [Water: gel]

    3:1

    Pot Life @ 20 ° C (3:1 ratio)

    Pot life @ 20 ° C (4:1 ratio)

    [Min]

    2,5-3

    3,5-4

    De-mould time @ 20ºC (3:1 ratio)

    De-mould time @ 20ºC (4:1 ratio)

    [Min]

    4,5

    5,5

    Full strength after

    [Min]

    5,5

    Processing

    This alginate 3D gel is chromatic. The dry white powder turns bright pink when you add water. As soon as the product starts to solidify, it becomes lighter pink and when it is white again, the mold is ready.

    If you are not familiar with this product, we recommend that you first do a small test with a coffee cup with 1 finger! Work with good cold water so that you have enough time.

    If you are going to pour the Alginate 3D gel: first choose a container that is not too small or too large. Weigh this container. Fill the container with water. Put the hands / hand in the water. You weigh the water that is still in the tank afterwards. (total weight of the bucket with water, minus the weight of the bucket) This is exactly the weight of water you need. Use a mixing ratio of Water: alginate = 4: 1 (if you are going to process gypsum you can also work with a mixture of water: alginate = 5: 1)

    If you are going to spat (face, belly or hand wreath): use a mixing ratio of Water: alginate = 3: 1. Note: spread the alginate quickly and keep it high until it has hardened. A thickness of 2-3 mm is already sufficient. Use cotton wool in the just wet applied alginate to make the alginate adhere better to plaster cast.


    The mixing ratio is by weight and NOT by volume. E.g. 500 grams of Alginate 3D gel with 2000 grams of water. If you suffer from lumps in the powder, we recommend that you first sieve them out of the pack before adding water. Mix the alginate with the water with a mixer in one go to a smooth porridge. Do NOT mix too long, a few lumps is not a problem.
    After mixing, immediately push the desired body part with the correct position into the mixture. Rub air bubbles away by hand and then keep the body part still. Now try to move as little as possible and make sure that you do not touch the edges of the mixing bowl. Then wait until the whole has completely cured in +/- 5 minutes. The mold is now ready and can be cast with plaster, concrete, wax or many other castings. The mold can be used once and has a lifespan of a few hours.

    Accelerate: The processing time (potlife) becomes much shorter if you use lukewarm or warm water.
    Delay: When you use colder water or salt-poor water (demineralised water), the curing takes longer.

    NOTE: there are postures of the hand that cannot be used properly. This is because air is trapped during the casting of plaster in the alginate. Because of this, finger tips will be missing.

    Make sure that the air can always go up (obliquely). If a finger is crooked it is not possible. Then the fingertip must touch the palm, so that the air can still go up through the palm. In the good examples of the fist and the shooting range, the fingertips that are bent touch the palm so that the air can escape through the palm.

    The bent fingers in the wrong examples do not touch the palm of the hand. The red spots indicate where the air is trapped and can no longer leave. That often means missing fingertips.

    Stand van de hand voor bodycasting

    Shelf life
    Provided that the 3-D Gel is kept in a sealed container in a cool and dry area, the shelf life is 1-2 years. After opening and sufficiently sealing the shelf life will be about 6 months.

    Safety
    To our knowledge, the 3-D gel completely harmless to humans and the environment.
    For more information, see the medical data sheet.

     

    Product Information Alginate 3D Gel

     

    guidelines

       

    Baby hand 0-1 years

    550 ml beaker

    96gr. alginate + 
    384 gr. water

    150 gr. plaster + 
    35 gr. water

    Children's Hand 2-10 years

    1100 ml beaker

    168 gr. alginate + 
    672 gr. water

    300 gr. plaster + 
    75 gr. water

    Woman Hand / child> 10

    1100 ml beaker

    204 gr. alginate + 
    816 gr. water

    600 gr. plaster + 
    150 gr. water

    male hand

    1900 ml beaker

    288 gr. alginate + 
    1152 gr. water

    800 gr. plaster + 
    200 gr. water

     

    Specifications

    Specifications for: Alginate 3D Gel - 5 kg.

    • Color White
    • end Color White
    • Working Time @ 20°C 3 –5 minutes
    • tensile strength 0.6 N/mm2
    • Mixing ratio A: B Algiante : Water 25:100 (weight)
    • View all specifications
    • compressive strength > 0.8 MPa
    • Density -

    Product tags

    Reviews

    Compare products Delete all products

    You can compare a maximum of 3 products

      Hide compare box
      Alginate 3D Gel - 5 kg.

      Alginate 3D Gel - 5 kg.

      € 99,50

      Please accept cookies to help us improve this website Is this OK? YesNoMore on cookies »