Back

Fake glass Set / Movie glass

  • Fake glass Set / Movie glass
  • Fake glass Set / Movie glass
  • Fake glass Set / Movie glass
  • Fake glass Set / Movie glass
  • Fake glass Set / Movie glass

1-2 days

    € 13,95

    Add to wishlist

    • Besteld voor 16 uur? Vandaag nog verzonden! TooltipOp vrijdag voor 15.00 uur
    • Kopen bij specialist
    • Verzending €3.95, gratis vanaf €50 (NL)
    • Not good? Money Back!
    Placeholder4.7

    Ratings

    Product description

    Fake glass Set / Movie glass

    Easily create a fake glass item

    Read the full product description

    Film glass

    ++BLUE++ This is a polyester resin to create glass like items and broken glass effects ++ENDBLUE++

    Description
    With this Film glass set based on crystal clear polyester you can easily create items that look like glass or mimic broken glass effects.

    To use it as breakable glass, please cast thin walled items.

    It is also great to use for water effects for scale models. The use of filler fumed silica will make it paste like.

    Technical data

    Mixing ratio (weight)

     

    [A: B]

     

    100: 1.5-2.5 (two is best)

    Processing time at 1% peroxide at 20oC

     

    [Min]

     

    30-45

    De-mould time @ 20 ºC *

     

    [Hours]

     

    More than 2 hours, depending on thickness and temperature

    Color (UV-resistant)

     

    [-]

     

    Bright but discolores slightly  over time

    Viscosity @ 20 ° C

     

    [MPa s]

     

    900

    Density after curing

     

    [G / ml]

     

    1.22

    Flexural strength DIN EN 63

     

    [N/mm2]

     

    90

    Modulus of elasticity DIN 53 457

     

    [N/mm2]

     

    3500

    Tensile strength DIN EN 61

     

    [N/mm2]

     

    55

    Impact strength DIN 53 453

     

    [KJ/m2]

     

    8

    Tg glass transition temperature DIN 53 445

     

    [oC]

     

    80

    Stable up to (ISO 75)

     

    [oC]

     

    70

    Shrinkage (room temperature hardening) DIN 16 946

     

    [%]

     

    7

    Refraction index  DIN 53 491

     

    -

     

    1.55

    Dielectric constant DIN 53 483

     

    -

     

    3

    Dielectric loss at 106 Hz DIN 53 483

     

    -

     

    0.02

    Surface resistance DIN 53 482

     

    [Ω]

     

    1013

    Spec interior resistance DIN 53 482

     

    [Ω.cm]

     

    1015

    * Full cure @ 20 ° C after a few days. Please note that touching the casting before it is completely cured migh leave finger prints.

    Processing
    Add the A and B components in the proper weight parts together (100: 1.5-2.5) and mix the components well. For smaller castings, we recommend adding some more harder (2 to 2.5%) in larger castings just slightly less (1.5 to 2%)
    Pour the mixed product with a constant and thin jet into the mold. Take care not to entrpa air. Excessive heat in castings of more than 15mm thickness can be prevented by pouring several successive layers (allow to the layer set before the following layer is added). De-mould only after the specified time has elapsed or better yet after several days. The thermal and mechanical properties will develop rapidly, but it is possible to improve the thermal behavior by post curing the casting for 2 hours at 60 oC for every 2 cm of thichkness.  It is recommended to process the products at 20 °C and to pre-heat the mold to 40 oC. After the cast has de-aired you can place it in an oven at 40 oC to speed up the curing process.

    Important
    Always work in a well ventilated area and use protection gloves and safety goggles.

    Packing
    The Film glass Set is a kit. The two components thus come together.

    Durability
    Properly sealed and stored out of direct sunlight around 15 -25oC the shel life is at least 6 months.

    Safety
    The products in liquid form are harmful to health. Skin contact with one or both of the components must be prevented. Prolonged or frequent use of this product will cause vapors to be irritating to  your respiratory system. When handling this product, wear protective gloves. Always work in a well ventilated area. For further information see Safety Data Sheet.

    ++DOWNLOADS++

    DocumentDownload
    Product Information

    ++USP++

    • Crystal clear
    • UV resistant
    • Designed for easy use
    • Low viscosity (liquid)
    • Can be molded without vacuum.

    Specifications

    Specifications for: Fake glass Set / Movie glass

    • Shore (A) 20
    • Color A Comp. Grey / White
    • Color B Comp. Blue
    • end Color White
    • cured density 0.75 g/cm3
    • View all specifications
    • viscosity mixture Pasta
    • Mixing ratio A: B 25:100
    • Working Time @ 20 ° C 15 minutes
    • Curing time @ 20 C 6 hours
    • tensile strength 0.6 N/mm2
    • extensibility 450%
    • tear Strength > 20 N / mm
    • linear shrinkage<0,1%

    Reviews

    Compare products Delete all products

    You can compare a maximum of 3 products

      Hide compare box
      Fake glass Set / Movie glass

      Fake glass Set / Movie glass

      € 13,95

      Please accept cookies to help us improve this website Is this OK? YesNoMore on cookies »