Laminating Epoxy Resin, 0.1 to 2 cm thick lamination

In stock

  • Article code: S10951

✔ Heat resistant up to 80 ° C
✔ Can be processed up to 10 kg * in 1 go
✔ Clear, colorless, UV blocker
✔ Quite liquid
✔ Shore D 90 (hard)
✔ Castings 1 mm <> 20 mm
✔ 30 minutes working time *
✔ Mixer. (Weight) 100:33

€23,55€ 18,84
€ 15,57 Excl. tax

Add to wishlist

Buy now Pay in 14 days with Klarna

  • Fast shipping! Everything available from stock
  • Buy from the specialist
  • Extended internal Laboratory
  • More than half a million satisfied customers

Product description

Laminating Epoxy Resin, 0.1 to 2 cm thick lamination

The low viscosity (very fluid) of this clear epoxy casting resin makes it suitable for detailed casting of small objects and is suitable for 0.1 cm castings. up to 2 cm thickness.

This epoxy resin is very suitable for pouring floors with different effects, pouring over works of art, pouring over photos, etc. It contains a UV blocker, which makes yellowing less likely. With the final hardness of Shore D 90 you get a very hard end result.

You can find a less liquid, viscous epoxy resin here:SAM HT Laminating Epoxy Resin - Heat resistant up to 140°C
You can find an epoxy resin for thicker castings here: SAM River & Art Epoxy Resin - 1 to 10 cm. pouring thickness


Mixing ratio by weight: A:B = 100:33
Mixing ratio by volume: A: B = 100:50
Color: clear, colorless
Processing time 100 gr. at 25°C: 30 minutes*
Curing time at 25°C: 8-10 hours*
Fully cured after: 3 days
UV blocker: yes
Hardness: Shore D 90
Density: 1.09 g/cm³
Viscosity: 400-700 cPs
Temperature resistant up to: 80°C
Minimum casting thickness:0,1 cm 
Maximum casting thickness: 2 cm
Maximum quantity to be processed in one go:10 kg**

*With a larger quantity, the processing time and curing time will be shorter!

**We recommend not to process the maximum amount in one go if you have little experience. If you want to do this, work at 18°C with a mixing bucket with a large bottom/diameter and now that you have a very short processing time!


Make sure that the surface is tight and not porous. This can cause air bubbles in the epoxy. Use a thin layer of epoxy or primer for this.

Always use safety gloves and goggles when handling this material. Process the resin at room temperature (18-25oC) and at a humidity lower than 70%. In order not to get any deformation in the surface, the temperature must remain constant during the entire curing process. Also avoid direct sunlight through a window and prevent drafts.

Add the A and B component in the correct ratio (A: B = 100: 33 by weight) and mix well. Allow enough time for mixing (2-3 minutes) and make sure the corners and bottom of the mixing bowl are included. Optionally, you can pour the whole thing into a second bowl and mix it again. Now add any color effects and stir again. Let air bubbles escape for a minute. If necessary, help by vibrating / rattling the tray. Please avoid the epoxy getting to hot in the mixing bowl. Start pouring immediately if needed.

The Epoxy resin is now ready for use. Apply the mixture with a brush or pour the mixture into your mold or prepared model with a thin stream.

Please note that you should use a large-bottomed mixing bowl for larger quantities. Avoid creating a thick layer of epoxy in the mixing bowl as this heats up very quickly!

Removing airbubbles works best with Air extractor or by using a flame. Please do not use flames if you thinned the epoxy down with alcohol or other flamable products.

If you are going to apply the resin in several layers (multi-layer work):

Wet on wet:

When pouring a second layer of a liquid into a first layer of epoxy liquid, you have to make sure that the exothermic reaction has completely worn off. An exothermic reaction is a reaction that releases energy. In this case, heat.
If you want to be sure of this, you wait until the second layer is no longer sticky, but still retains a fingerprint when touched.

Wet on dry:

It is necessary to sand the previous layer and make it dust and grease free.


Product stored in tightly closed packaging between 15 and 25°C has a shelf life of at least 1 year.

Security requirements

H-CodeHazard Statements

H302+H312 - Harmful if swallowed or in contact with skin.

H315 Causes skin irritation.

H317 May cause an allergic skin reaction.

H318 - Causes serious eye damage.

H319 Causes serious eye irritation.

H411 ​​Toxic to aquatic life with long lasting effects.

EUH205 - Contains epoxy compounds. May cause an allergic reaction.

P-Code Precautionary Statements

P102 - Keep out of reach of children.

P270 - Do not eat, drink or smoke when using this product.

P271 - Use only outdoors or in a well-ventilated area.

P273 - Avoid release to the environment.

P280 - Wear protective gloves, Protective clothing, Eye protection.

P301+P310 - IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.

P301+P330+P331 - IF SWALLOWED: rinse mouth — DO NOT induce vomiting.

P303+P361+P353 - IF ON SKIN (or hair): Take off immediately all contaminated clothing — rinse skin with water/shower.

P304+P340 - IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.

P305+P351+P338 - IF IN EYES: Rinse cautiously with water for several minutes. remove contact lenses, if possible; keep rinsing.

P501: Dispose of contents and container according to local/regional/national/international regulations.



EN - Product Information SAM Laminating Epoxy Resin.pdf

EN - Safety Data sheet Laminating Epoxy Resin A.pdf

EN - Safety Data sheet HT Epoxy Resin B Hardener.pdf


Specifications for: Laminating Epoxy Resin, 0.1 to 2 cm thick lamination

  • Color A Comp. Clear
  • Color B Comp. Clear
  • end Color Clear, colorless
  • Mixing ratio A/ B 100: 33 in Weight. 100: 50 in volume
  • cured density 1.09 g/cm2
  • View all specifications
  • viscosity mixture 400-700 cPs
  • Working Time 30 minutes
  • Curing time 8-10 hours (2 days complete)
  • UV-blocker Yes
  • Shore D 90
  • Maximum casting thickness 2 centimeters
  • Minimum casting thickness 0.1 centimeters
  • Kg to cast in one go 10 Kg, under certain conditions
  • Maximum temperature resistance cured up to 80° C
  • Mainly used for
  • Compressive strength Kg/mm² 13,4
  • Flexural strength Kg/mm² 23
  • Volumetric resistance Ohm-m 10^15
  • Water absorption %<0,15
  • UV Blocker added? Yes
Do you have a question about this product?

Do you have a question about this product?

Our employee is happy to help you find the right product

Related products

Recently viewed

    • S.A.M. Laminating Epoxy Resin,   0.1 to 2 cm thick lamination

    Laminating Epoxy Resin, 0.1 to 2 cm thick lamination

    -20% Sale

    €23,55 € 18,84 € 15,57 Excl. tax

    ✔ Heat resistant up to 80 ° C
    ✔ Can be processed up to 10 kg * in 1 go
    ✔ Clear, colorless, UV blocker
    ✔ Quite liquid
    ✔ Shore D 90 (hard)
    ✔ Castings 1 mm <> 20 mm
    ✔ 30 minutes working time *
    ✔ Mixer. (Weight) 100:33

      Compare products Delete all products

      You can compare a maximum of 3 products

        Hide compare box
        Laminating Epoxy Resin,  0.1 to 2 cm thick lamination

        Laminating Epoxy Resin, 0.1 to 2 cm thick lamination

        23,55 € 18,84

        Please accept cookies to help us improve this website Is this OK? YesNoMore on cookies »