T 51 B component for condensation curing silicone for processing polyester

  • T 51 B component for condensation curing silicone for processing polyester

In stock

  • Article code: S11333

✔ 5% dosage
✔ dry, stretchy result
✔ Can be used neat or mixed
✔ Low shrinkage (< 0.3%)
✔ Better resistance to polyester
✔ Mixing ratio (Weight) 100:5

€ 6,05
€ 5,- Excl. tax

Add to wishlist

Buy now Pay in 14 days with Klarna

  • Fast shipping! Everything available from stock
  • Buy from the specialist
  • Extended internal Laboratory
  • More than half a million satisfied customers


Product description

T 51 B component for condensation curing silicone for processing polyester

This hardener works on all condensation silicones. This T51 hardener from Wacker makes the silicone more resistant to polyester.

This B component may also be mixed with other condensation B components to achieve a speed of your choice with the properties of the other B components. Common mixtures are:

10% T47 with 90% T51, so for 100 grams of A there is 4.5 grams of T51 with 0.5 grams of T47


You can easily mix the silicone condensation 20 or other condensation silicones by hand or machine. Mix the A and B components carefully and in the stated ratio.

T51 opinion = 5%, so for 100 grams of A component you use 5 grams of Wacker T51 hardener (B component).

You can use 0.5% less or more hardener. If you use less hardener, curing takes longer and air bubbles have more time to escape. Be careful not to use too little hardener, as the silicone may no longer harden (properly). With more hardener, curing will proceed faster, meaning the mold will be ready sooner. The disadvantage is that the mold will also age sooner and shrink more.

Process the mixture within the pot life (processing time) and never make more than you can process within the pot life. Wait until the mold has completely hardened before removing the mold.

Please note: Pot life (processing time) and demoulding time are highly dependent on the mixing ratio and humidity! When adding more silicone B (harder) or at higher humidity, the pot life and demoulding time become shorter!

Brushing or spreading

If you want to spread/spread/iron the silicone on something, you can add Thixo C (0.6%-2%) (usually 1%). Thixo C is a thickener and makes it possible to spread the silicone. You should take into account that in this case the mold must be provided with a support cap. This support cap can consist of plaster cast, an epoxy support cap, or acrylic resin with thickener and glass fabric /

Shelf life
Provided the silicone is stored in closed packaging, cool and frost-free, the shelf life is at least 1 year.

Safety requirements
Use splash goggles, suitable liquid-tight gloves, an apron and work in a well-ventilated area. See Safety Data Sheet for more information

Further important safety information

H-Code hazard statements

H226 Flammable liquid and vapour.

H319 Causes serious eye irritation.

H332 Causes serious eye irritation.

H335 Harmful by inhalation.

Suspected of harming the unborn child.

Causes damage to organs through prolonged or repeated exposure.

May have long lasting harmful effects on aquatic organisms.

P-Code precautions

P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. Do not smoke.
P233 Keep container tightly closed.
P260 Do not breathe vapour/aerosol.
P271 Use only outdoors or in a well-ventilated area.
P273 Avoid release to the environment.
P280 Wear protective gloves/protective clothing/eye protection.
P243 Take measures to prevent static electricity discharges.
P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.
P312 Call a POISON CENTER/doctor if you feel unwell.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. remove contact lenses, if possible; keep rinsing.
P337+P313 If eye irritation persists: Get medical advice/attention.
P370+P378 In case of fire: extinguish with water jet, extinguishing powder, foam or carbon dioxide.
P403+P235 Store in a well-ventilated place. Keep cool.
P501 Dispose of contents/container to waste disposal.



Product information sheet Silicone Condensation 20

EN - Safety Sheet Wacker_Catalyst_T_47.pdf





Specifications for: T 51 B component for condensation curing silicone for processing polyester

  • Shore (A) 23~26
  • Color A Comp. White
  • Color B Comp. Brown Yellow
  • end Color Beige
  • cured density 1,08 g/cm3
  • View all specifications
  • viscosity mixture 18.000 ± 2.000 mPa s
  • Mixing ratio A/ B 100:2
  • Working Time >120 minutes
  • Curing time 48 hours
  • tensile strength 40 Kg/cm2
  • extensibility 450%
  • tear Strength 28 Kg/cm
  • Linear shrinkage<0,3%
  • Curing method Alkoxy/ Alcohol
  • Volume resistivity Not measured
  • Permittivity Not measured
  • Heat capacity [Kj/Kg Kelvin] NA
  • Heat conductivity [W/mK] NA
  • Product category Condensation Silicone

Product tags

Do you have a question about this product?

Do you have a question about this product?

Our employee is happy to help you find the right product

Related products

Compare products Delete all products

You can compare a maximum of 3 products

    Hide compare box
    T 51 B component for condensation curing silicone for processing polyester

    T 51 B component for condensation curing silicone for processing polyester

    € 6,05

    Please accept cookies to help us improve this website Is this OK? YesNoMore on cookies »